商用無料の写真検索さん
           


Kid Flier 6 1/2 plan: balsa wood stick and copier paper glider for first-time builders and fliers : 無料・フリー素材/写真

Kid Flier 6 1/2 plan: balsa wood stick and copier paper glider for first-time builders and fliers / wbaiv
このタグをブログ記事に貼り付けてください。
トリミング(切り除き):
使用画像:     注:元画像によっては、全ての大きさが同じ場合があります。
サイズ:横      位置:上から 左から 写真をドラッグしても調整できます。
あなたのブログで、ぜひこのサービスを紹介してください!(^^
Kid Flier 6 1/2 plan: balsa wood stick and copier paper glider for first-time builders and fliers

QRコード

ライセンスクリエイティブ・コモンズ 表示-継承 2.0 一般
説明This is the Kid Flier 6 1/2, a flying model (toy) glider that any child or adult can build in less than an hour. It will glide nicely indoors and work outdoors in light winds. Its not meant for muscular javelin throws like an all balsa wood glider, but it can be slid gently into the air, glide across a room, through a door. But not really for loops. Gentle is the key.An improved, color, version of this drawing can be found at www.flickr.com/photos/wbaiv/8606241195/. I'm leaving this version here. With 910 views, (3/31/13) there must be something right about it...The single most important thing is the wing. Its a 2 1/3" (aka 2 3/8", aka 60mm) strip of paper, 8 1/2 inches wide in North America, 2xxmm, A4, in the rest of the world. The first 1/4 of the paper- 2/3", aka 11/16", aka 15mm, is folded down and glued with common "glue stick" to the second 1/4. This makes the paper double thick at the front, and regular thickness in the back. Upside down, that's "c=----" The FOLDED EDGE is the structural stiffener for the wing. If you glue two strips together, not folded but cut separately, it will not be as strong. You could use a very thin bit of white glue instead of glue stick, but the glue stick is lighter and dries faster.Once the leading edge is folded, you'll notice that the wing will balance at approximately 1/3 back from the leading edge. This 1/3 proportion is the only actual number you need to build flying model or flying toy airplanes. If you push the wing forward very gently, in a horizontal position, as if attached to the rest of a toy airplane, it will fly. www.flickr.com/photos/wbaiv/5702863214/ Keep trying. Sometimes it will slide off to one side or the other, sometimes it will flop side over side, but sometimes, it will fly straight and level, descending. Keep trying. www.flickr.com/photos/wbaiv/5702294365/For physics fans in the audience, the potential energy of the height above ground level is being converted to the kinetic energy of wing falling, but also to forward motion in the air. As the wing descends, it displaces the air below it. By folding back the front 1/4, you've changed the density of the wing, moving the center of balance forward. The wing tends to be a bit nose-down, a bit inclined. The air squeezed out by its falling is pushed back and the equal and opposite reaction pushes the wing forward.Now take a moment to cut (scissors work fine) one 6 1/2" long and two 1" long pieces of 1/16" square balsa wood. The long one is the fuselage, the short ones are wing mounts. There are patterns with dimensions at the top of the plan. Make one piece that fits each set of lines. That's 1.5mm square by about 160 to 165mm for the fuselage, about 25mm for the pair of wing mounts. Also cut out a 1 3/4" (1.75") piece of 1/8" balsa wood for the nose block. That's 44 or 45mm, of 3mm square. www.flickr.com/photos/wbaiv/5702861754/Mark the first 1" (25mm) at BOTH ends of the long stick. I'm showing the marks as "." below. I. . . . . . . . . . . . . . . . . . . . bottomfront end . . .===.==============.=== . . .back end. . . . . . . . . . . . . . . . . . . . topNow take a nail file or sanding stick or sand paper and taper (sand down) ONE end, over the 1" length, from 1/16" to nothing. That's the back of the plane, where the horizontal stabilizer goes. The area removed is solid red in the drawing above. www.flickr.com/photos/wbaiv/5702292633/. . . . . . . . . . . . . . . . . . . bottom . . . . ""--,, <-- TAPERfront end . . .===.==============.----- . . .back end. . . . . . . . . . . . . . . . . . . . topThe thin end is the TOP of the fuselage, The wing will be glued flat onto the fuselage, the horizontal stabilizer will have its leading edge at the lower edge of the fuselage, and the trailing edge at the upper edge of the fuselage. The relative difference in angle is very important.'m sorry its drawn upside down, but I don't have a character that will line up with the UPPER of the two lines making an equals sign "--==_". Whereas, the dash sign, "-" which you might expect to fit right down the middle of the equals, lines up more with the lower line. Oh well.Now mark the SECOND 1 inch (25mm) of the front of the stick:. . . . . . . . . . . . . . . . . . . bottom . . . . ""--,, <-- TAPERfront end . . .===.===.===========.----- . . .back end. . . . . . . . . . . . . . . . . . . . topUse white or carpenters' to glue the two 1" (25mm) pieces on the SIDES of the long stick, the fuselage, starting at the 1" (25mm) mark at the OTHER end of the stick and going toward the middle. (Use Courier New or another fixed spacing font for this part:)From the side, upside down, this will look like:. . . . . . . . . . . . . . . . . . . bottom front end . . .===.===.===========.----- . <-- TAPER. . .back end. . . . . . . . . . . . . . . . . . . . topThis view doesn't show the short pieces because they're along the long piece. But it does show the taper from the full thickness of the fuselage to nothing, over the last 1 inch / 25mm.From the bottom, lying upside down on a sheet of wax paper or plastic wrap,, it will look like:. . . . . . . . . . . . . . . . . . . bottom . . . . . . . . . . . . . . ===front end . . .===.===.===========.----- . <-- TAPER. . .back end. . . . . . . . . . . . . . ===. . . . . . . . . . . . . . . . . . . . topExcept the sides of the short pieces will be actually touching the sides of the long piece. From top or bottom, you can't really see the tapper at the back end, but I want you to see that the wing mounts are 1 inch (25mm) from the FRONT of the stick, and the taper is in the LAST 1 inch (25mm) of the stick. In the following side views, I'm using "[[[]]]]" to mark where the wing mounts are:===.[[]]]].===========.----- . . . <-- TAPER. . .back endFinally, glue the 1/8" (3mm) piece to the UNDERSIDE of the front of the fuselage. That is, to the other end of the same side of the sanded, tapered end, NOW it looks like:. . . . . . . . . . . #####. . . . .bottom front end . . . ===.[[]]]].===========.----- . . . . back end. . . . . . . . . . . . . . . . . . . . . . top.Put the sticks aside to dry for a couple of minute and play with the wing a bit more. A really gentle launch will work remarkably well, and, if you think about it, the only purpose to the rest of the airplane is to make it easier to launch the wing successfully. And control the direction it goes in. Now cut out the 1" X 1" (25mm X 25mm) copier paper square for the fin, and the 1" X 2" (25 X 50mm) rectangle for the horizontal stabilizer. Mark a center-line across the 1" dimension of the horizontal stabilizer, dividing it into 2, square, halves. Lightly apply glue to the diagonal , tapered, underside at the back of the stick. The one you sanded:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . glue. . . . . . . . . . . #####. . . . . bottom . . . vvvvfront end . . . ===[[[]]]]============----- . . . . back end. . . . . . . . . . . . . . . . . . . . . . top.Lay the centerline of the horizontal stabilizer onto the glue, double check that the stabilizer is straight across the stick and equal sizes on both sides of the stick:. . . . . . . . . . . #####. . . . . bottom . . . ___ <-- horizontal stabilizer front end . . . ===[[[]]]]============.----- . . . . back end. . . . . . . . . . . . . . . . . . . . . . top.From the bottom, the whole thing, upside down, should look something like: . . .wing . . .mount . . . . v. . . ====. . . . . . . . . . . . . .| . . |<-- horizontal stabilizer #####==.============.|:::::| back end. . . ====. . . . . . . . . . . . . .| . . |===[[[]]]]============-----If the stick is 'right side up", the trailing edge of the horizontal stabilizer will be higher than the leading edge. This will tend to push the tail down and thus the nose up- the opposite of what the wing does when you fly it by itself - it tends to rotate toward nose-down and go flop flop flop if not launched really steadily. Putting a stabilizer out behind the wing is like putting feathers on an arrrow- they will tend to keep it pointing the direction it was launched, if they're straight. By adding the tail-down/nose-up angle, the horizontal stabilizer dynamically balances the wing's natural nose-down tendency. The stabilizer holds it very slightly nose-up. If the wing pitches nose-down, it raises the horizontal stabilizer, causing it to be pushed down by more airflow. So the two forces balance. Like the arrow feathers, or the rudder on a surf-board, the system is stabilized by negative feedback. Turn the nose up, and a restoring force pushes it back down. Push it down and the restoring force pushes it back up.
撮影日2011-03-13 00:52:44
撮影者wbaiv
タグ
撮影地


© 名入れギフト.com

こちらもおすすめです→ カエレバ(同一商品の複数ショップリンク一発作成) | Amazon search | 楽々お任せリンク | Affiliate Helper